Open Access

PROCEEDINGS

Jian Wang^1,*, Haitao Hei¹, Yonggang Zheng¹, Hongwu Zhang¹, Hongfei Ye¹
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.010916
Abstract Icing is a ubiquitous phenomenon in nature and widely observed in the micro/nanoconfinement, e.g., two-dimensional ice growth on Au surface, nanoconfinement-induced phase change, nanodroplet freezing on surface, etc. These complicated and abstruse processes and behaviours demand deep understanding from the microscale level by the aid of molecular dynamics (MD) simulation [1]. However, it is still a great challenge to accurately describe the ice and liquid water simultaneously with the present water models [1,2]. In response to this, we propose a series-parallel machine learning (ML) approach consisting of classification back-propagation neural network (BPNN), parallel regression BPNNs… More >

View

81

Download

63

Open Access

PROCEEDINGS

Hongfei Ye^1,*, Dong Li^1,2, Hongwu Zhang¹, Yonggang Zheng¹
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.010938
Abstract Due to excellent physical performance and potential application in the nanoscale fluid channel, 2D transition-metal dioxides and dichalcogenides with 1H phase are of great interest. Their mechanical property attracts much attention but the accurate evaluation still faces challenges because of the ultrasoft and ultrathin structure. In this work, we establish an analytical atom-based molecular mechanics model to predict the elastic modulus, Poisson’s ratio and shear modulus of the single-layer 2D transition-metal dioxides and dichalcogenides. The proposed method is validated through the calculation of the mechanical property of Molybdenum disulfide (MoS₂). The results indicate that the elastic… More >

View

79

Download

59

Open Access

PROCEEDINGS

Changtao Wang¹, Honghua Dai^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.010943
Abstract Orbital uncertainty propagation is fundamental in space situational awareness-related missions such as orbit prediction and tracking. Linear models and full nonlinear Monte Carlo simulations were primarily used to propagate uncertainties [1]. However, these methods hampered the application due to low precision and intensive computation. Over the past two decades, numerous nonlinear uncertainty propagators have been proposed. Among these methods, the state transition tensor (STT) method has been widely used due to its controllable accuracy and high efficiency [2]. However, this method has two drawbacks. First, its semi-analytical formulation is too intricate to implement, which hinders… More >

View

68

Download

54

Open Access

PROCEEDINGS

Kai Wang^1,2,3, Lihua Yang^1,2,3,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.011018
Abstract Although offset-halves journal bearings (OHJBs) are widely used in marine powertrains, the research on nonlinear tribo-dynamics is still limited, particularly under dynamic loading. To overcome such limitations, this study proposes a novel dynamic model that couples the influences of step load and thermoelastohydrodynamic (TEHD) effect. Based on the numerical model, a transient TEHD analysis for dynamically loaded OHJBs is done. Moreover, a modified stability criterion is developed. Nonlinear behaviors and transient stability of OHJBs under step load are systematically studied. The correlations of bearing characteristics such as the maximum film temperature, minimum film thickness, maximum More >

View

68

Download

52

Open Access

PROCEEDINGS

Yubo Jiao¹, Wei Wang^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.011157
Abstract The source-sink matching optimization problem is one of the more important aspects of carbon capture and storage (CCS) system planning studies, and a large number of studies have been conducted using mathematical modeling to assess the feasibility of deployment in the planning region, thus providing important decision support. A framework of optimization system applicable to source-sink matching analysis was constructed based on the structural relationship between directly connected sources and sinks, taking into account multiple factors (transport characteristics, CO₂ injection rate and connection period, etc.), which can ensure the feasibility of CO₂ pipeline transportation operation and… More >

View

78

Download

54

Open Access

PROCEEDINGS

Yu Guo¹, Lianxiong Chen¹, Hui Liu^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.011187
Abstract In the topology optimization of the multiscale structure, ensuring connectivity between adjacent microstructures, controlling the design space of microstructures, and reducing calculation amount and improving calculation efficiency are three basic challenging issues currently faced. To address this, this paper presents a data-driven approach for the integrated optimization of macroscopic topology and microscopic configuration of graded functional cellular structures. At the macro level, a topological description function is introduced to realize the topological control of the macro structure. At the micro level, several cutting functions are used to realize the control of the configuration and size… More >

View

86

Download

63

Open Access

PROCEEDINGS

Tingting Zhu¹, Pei Lian¹, Wenxuan Du^2,3, Chenxu Zhang^2,3, Yinggang Miao^2,3, Haiying Wang^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.011281
Abstract Penetration of syringe needles into the rubber plug of vials occurs daily in usual medical operation, but in nature, it is a complex mechanical process concerning the deformation, friction and failure of materials. Micro particles could be generated during the fracture process of plug and needle friction during penetration. Actually, the structural configuration of needle pin plays an important role besides of plug itself. In this work, mechanical behaviors of butyl rubber and needle material are obtained firstly, after performing various strain rate experiments based on Instron 5848 machine and Hopkinson bar technique. And their… More >

View

79

Download

50

Open Access

PROCEEDINGS

Xiaojiang Liu^1,*, Zhongze Gu¹, Kun Zhou²
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.011320
Abstract Surfaces with overhanging microstructures play an essential role in surface wettability. Typically, surfaces with tightly-distributed multiply symmetric re-entrant microstructures enable the liquid suspension toward water, oil, and even n-perfluorooctane, whose surface tension is as low as 12.0 mN/m [1-4]. In contrast, surfaces with asymmetric re-entrant microstructures are favorable for unidirectional liquid spreading, where the liquids exhibit a small contact angle on the surfaces [5]. These fantastic wettability behaviors can be attributed to three-dimensional (3D) features of the overhanging microstructures, where the edge effect and Laplace pressure difference are generated on the overhanging microstructures. Based on… More >

View

61

Download

51

Open Access

PROCEEDINGS

Wei Ji¹, Yingchun Bai^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.011338
Abstract The superior stiffness-to-weight and strength-to-weight mechanical advantages of shell-infill structures can be fully exploited through concurrent design of the entire topology and infill configuration. This inherent design freedom can be guaranteed by additive manufacturing, through which complicated geometry can be fabricated. The existing approaches are typically focused on topology optimization with porous infill [1-3], un-prescribed lattice configuration with uniform density [4-8], or prescribed single lattice configuration with non-uniform density [9-10]. Towards higher performance yet lightweight, this work proposes a concurrent topology optimization approach to directly generate shell-infill structures in which the inner infill consists of… More >

View

98

Download

56

Open Access

PROCEEDINGS

Yuntao Lei¹, Wenbin Wu^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.011365
Abstract The underwater explosion could cause the serious damage to the naval ships. Investigating the underwater explosion problem is crucial for the development of marine military power. During the recent years, the underwater explosion dynamics in the homogeneous fluid field has been investigated by lots of researchers. However, there often exist sound speed thermoclines in the real ocean environment, which leads to a more complex fluid environment than the homogeneous fluid. The corresponding numerical calculations become more complicated. In order to fully understand the underwater explosion dynamics in the real ocean environment, we perform the numerical… More >

View

66

Download

59

Open Access

PROCEEDINGS

Jiayu Chen¹, Yingchun Bai^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.011393
Abstract Mega-casting techniques are widely used to manufacture large piece of thin-walled structures for vehicle body in Automotive industries, especially with the rapid growing electric vehicle market. Topology optimization is effective design method to reach higher mechanical performance yet lightweight potential for casting structures [1-3]. Most of existing works is focused on geometric-type casting constraints such as drawn angle, partion line, undercut, and enclose holes. However, the challenges in mega-casting arise from the complexities in the casting process such as filling and solidification, and the corresponding defects have larger influences on the structural performances [4-6]. Partial… More >

View

116

Download

75

Open Access

PROCEEDINGS

Wenxuan Du¹, Zhongwei Mou², Xuanfu He¹, Jianping Yin¹, Yinggang Miao^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.011421
Abstract High-speed friction and wear are usually occurring in the service life of advanced equipment, and their behavior even influences service safety. However, there is still technique gap in accurately obtaining the parameters during dynamic friction induced by high-speed equipment. This gap is primarily stemmed from the available dynamic friction loading techniques with poor controllability. In this work, a novel dynamic friction apparatus is designed based on split Hopkinson bar technique. The loading principle is from stress wave generated by striker bar hitting the incident bar, which forces the sandwiched friction pair to slide with a… More >

View

76

Download

58

Open Access

PROCEEDINGS

Jinxing Liu^1,*, Binying Wang¹, Changqing Peng¹
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.011544
Abstract Unlike classical condensed matters with the characteristic microstructural size far smaller than the undergoing wavelength, lattice metamaterials call for a kind of subwavelength continuum modeling, which should be able to provide successful predictions throughout the first Brillouin zone. We classify lattices into two groups. The first category stands for the mass-spring systems composed of dump masses and massless springs, for which three attempts have been made: the strain gradient continuum based on wavelength-dependent Taylor’s expansion [1, 2], Pade approximation [3] and Symbiotic Optimal Search (SOS) [4], respectively. The results of these newly developed models agree… More >

View

72

Download

59

Open Access

PROCEEDINGS

Jili Cai¹, Junyi Zhou¹, Hangyu Chen¹, Liang Huang¹, Wenming Jiang¹, Jie Liu¹, Zhongwei Li¹, Chao Cai^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.011946
Abstract Effectively obtaining tritium is one of the essential issues to realize commercial and controlled nuclear fusion [1]. Conventional lithium-containing ceramic tritium breeders with pebble bed configurations in fusion reactors have shown insurmountable structural drawbacks weakening tritium extraction, including inherently low packing fractions, extensive stress concentrations, and low thermal conductivity. Therefore, extensive efforts have been devoted to enhancing tritium extraction by improving the design of tritium breeders and addressing structural drawbacks [2-4]. In this study, porous block configurations were proposed to replace conventional pebble bed configurations for the ceramic tritium breeder. Utilizing fluid-solid coupled heat transfer… More >

View

75

Download

63

Open Access

PROCEEDINGS

Biao Wang¹, Yuxiang Peng^1,*, Wenhua Xu²
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.012061
Abstract The damage process of ship structures under near-field underwater explosions involves strong nonlinear coupling effects of multiple media, and its numerical simulation poses a serious challenge to traditional numerical algorithms. Based on previous research, this article first establishes a highly compressible multiphase flow numerical calculation model based on the high-precision Discontinuous Galerkin Method (DGM) and a ship elastic-plastic damage dynamic model based on the meshless Reproducing Kernel Particle Method (RKPM). Furthermore, we develop an algorithm for grid-independent dynamic expansion of cracks. Based on this, the Boundary Data Immersion Method (BDIM) is used to couple the More >

View

76

Download

58

Open Access

PROCEEDINGS

Zhao Zhang^1,*, Xiang Gao¹, Yifei Wang¹
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.012115
Abstract Wire arc additive manufacturing (WAAM) reveals its high efficiency for the fabrications in comparison with laser additive manufacturing. To reveal the relationship between arc settings and the microstructural evolutions, phase field model and Monte Carlo model are established for the simulation of the microstructural evolutions and dislocation dynamics model is established for the simulation of the anisotropic properties in WAAM. Numerical results are compared with Experiments to validate the proposed models. The length/width ratio of the formed grains in solidification becomes smaller when the scanning speed is decreased or the input powder is increased. The… More >

View

77

Download

74

Open Access

PROCEEDINGS

Jingjing Liu¹, Long Yu^1,*, Xiaoyan Li², Jing Liu²
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.012234
Abstract Owing to uncontrollable deformation during the launching process, significant hazards such as airbag blast failure can be observed, which can cause severe damage to surrounding structures. Involving gas-solid coupling and nonlinear damage, the analysis and evaluation of airbag blasts are complex. Therefore, an effective method to analyze the possible blast behavior by coupling smoothed particle hydrodynamics (SPH) and the finite element method (FEM) has been presented in this study. First, a single airbag compression model was established to calculate the stiffness curve and the rationality of the numerical method was verified through comparison with experiments.… More >

View

88

Download

68

Open Access

PROCEEDINGS

Xiaoyan Lu^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.012507
Abstract Ferroelectric materials usually experience various phase under external temperature, electric and stress fields. Unique properties such as piezoelectricity, dielectricity, polarization reversal, and phase transitions are widely used in various electronic devices. Particularly, the phase and domain structures, ferroelastic switching behaviors often play a crucial role in determining their dielectric and piezoelectric properties. Here, we report some abnormal behaviors in ferroelectric thin films and single crystals, from which, we build the Landau theoretical model for relaxor ferroelectric single crystals. Using this model, we studied the phase coexistence and the corresponding physical properties. Using the results, we More >

View

80

Download

59

Open Access

PROCEEDINGS

Biao Xia^1,2, Changxing Zhang^2,3,*, Zhanli Liu², Xue Feng²
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-2, 2024, DOI:10.32604/icces.2024.012764
Abstract Ceramics has become one of the most promising candidate materials in the aerospace field due to its advantages of high melting point, corrosion resistance, wear resistance, and high-temperature stability [1,2]. However, the inherent brittleness of ceramics makes it prone to thermal shock failure under high-temperature extreme environments, which can lead to sudden catastrophic accidents in the structure [3-6]. This paper takes the high-temperature resistant ceramic materials in the aerospace industry as the research object. And the dynamic crack propagation mechanism is analyzed. Through the computational method based on the extended finite element method (XFEM), the… More >

View

77

Download

61

Open Access

PROCEEDINGS

Lichao Zhang¹, Zhao Zhang^1,*
The International Conference on Computational & Experimental Engineering and Sciences, Vol.29, No.3, pp. 1-1, 2024, DOI:10.32604/icces.2024.012849
Abstract Powder flow can affect the temperature variations in directed energy deposition (DED). However, the direct coupling mechanism remains unknown. To solve this problem, the heat and mass transfer in additive manufacturing was simulated using dynamic coupling. The interactions between the multiphase flow and heat transfer were established. A comparison with experiment shows that the accuracy of the predictions of the numerical simulation regarding powder size distributions and temperature increases is higher than 95%. The average temperature increase of the metal powders with different weight functions was highly consistent in the simulation process. As the powder More >

View

83

Download

61