Shrikant Arunrao Thote^*, Netra Pal Singh

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 501-511, 2023, DOI:10.32604/fdmp.2022.021502 - 29 August 2022

Abstract The thermal behavior of pipes with a twisted tape inside (used to enhance heat transfer through the tube wall) is studied in the laminar flow regime. Oil is used as the work fluid with the corresponding Reynolds Number spanning the interval 200–2000. It is found that in such conditions the ‘Nusselt Number’ (Nu) gradually increases with reducing the tape twist ratio, whereas the friction factor is detrimentally affected by the presence of the tape (as witnessed by the comparison with the companion case where a plain tube is considered). In particular, it is shown that More >

Shuxian Gao¹, Yonggang Cao^2,*, Yuchuan Bai³, Yanhua Yang¹

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 487-500, 2023, DOI:10.32604/fdmp.2022.021149 - 29 August 2022

Abstract River bending is the major effect responsible for bed topography and bank changes. In this study, fluid velocity (measured by a three-dimensional Doppler advanced point current meter) and bed topographical data have been collected in 40 sections of an experimental model. The whole flume was composed of an organic glass bend, upstream and downstream water tanks, two transition straight sections, a circulation pump, and a connection pipeline. Each section has been found to be characterized by a primary circulation and a small reverse circulation, with some sections even presenting three more or more circulation structures. More >

Muhammad A. Sadiq^1,2,*, Nadeem Abbas³, Haitham M. S. Bahaidarah⁴, Mohammad Amjad⁵

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 471-486, 2023, DOI:10.32604/fdmp.2022.021133 - 29 August 2022

Abstract We present the results of an investigation into the behavior of the unsteady flow of a Casson Micropolar nanofluid over a shrinking/stretching curved surface, together with a heat transfer analysis of the same problem. The body force acting perpendicular to the surface wall is in charge of regulating the fluid flow rate. Curvilinear coordinates are used to account for the considered curved geometry and a set of balance equations for mass, momentum, energy and concentration is obtained accordingly. These are turned into ordinary differential equations using a similarity transformation. We show that these equations have More >

Yanhua Zhao^1,3,*, Wenhao Tian¹, Jianhua Liu¹, Dongqing Qian², Wei Meng¹, Jiaming Wang¹

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 451-470, 2023, DOI:10.32604/fdmp.2022.021035 - 29 August 2022

Abstract The process parameters of laser additive manufacturing have an important influence on the forming quality of the produced items or parts. In the present work, a finite element model for simulating transient heat transfer in such processes has been implemented using the ANSYS software, and the temperature and stress distributions related to 316L stainless steel thin-walled ring parts have been simulated and analyzed. The effect of the laser power, scanning speed, and scanning mode on temperature distribution, molten pool structure, deformation, and stress field has been studied. The simulation results show that the peak temperature, More >

Jinjing Zhang, Jia Li^*

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 303-313, 2023, DOI:10.32604/fdmp.2022.020723 - 29 August 2022

Abstract

A novel method to measure the flow rate in a wet gas is presented. Due to the presence of liquid, there is a deviation in the measurement of the gas volume flow rate obtained with standard vortex flow-meters. The proposed method is based on a correction factor determined through the application of an over-reading approach to a bluff body in mist flow. The correction factor is obtained from the slip velocity ratio, i.e., the ratio of droplet velocity to gas velocity, based on the analysis of the fluid velocity distribution in the pipeline section. It also

More > Graphic Abstract

Tingting Huo¹, Jiaquan Xue^2,*, Zhi’an Fu³

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 437-450, 2023, DOI:10.32604/fdmp.2022.020696 - 29 August 2022

Abstract The properties of polyurethane concrete containing a large amount of fly ash are investigated, and accordingly, a model is introduced to account for the influence of fly ash fineness, water ratio, and loss of ignition (LOI) on its mechanical performances. This research shows that, after optimization, the concrete has a compressive strength of 20.8 MPa, a flexural strength of 3.4 MPa, and a compressive modulus of elasticity of 19.2 GPa. The main factor influencing 28 and 90 d compressive strength is fly ash content, water-binder ratio, and early strength agent content. More >

Jiayu Ruan¹, Mingjing Lu^2,3, Wei Zhang⁴, Yuxi Zhang¹, Yuhui Zhou^1,*, Jie Gong¹, Fan Wang¹, Yuanxiao Guan¹

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 421-436, 2023, DOI:10.32604/fdmp.2022.020665 - 29 August 2022

Abstract After steam discharge in heavy oil reservoirs, the distribution of temperature, pressure, and permeability in different wells becomes irregular. Flow channels can easily be produced, which affect the sweep efficiency of the oil displacement. Previous studies have shown that the salting-out plugging method can effectively block these channels in high-temperature reservoirs, improve the suction profile, and increase oil production. In the present study, the optimal dosage of the plugging agent is determined taking into account connection transmissibility and inter-well volumes. Together with the connectivity model, a water flooding simulation model is introduced. Moreover, a non-gradient More >

Nourhan I. Ghoneim^1,*, Ahmed M. Megahed²

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 407-419, 2023, DOI:10.32604/fdmp.2022.020508 - 29 August 2022

Abstract A mathematical model is elaborated for the laminar flow of an Eyring-Powell fluid over a stretching sheet. The considered non-Newtonian fluid has Prandtl number larger than one. The effects of variable fluid properties and heat generation/absorption are also discussed. The balance equations for fluid flow are reduced to a set of ordinary differential equations through a similarity transformation and solved numerically using a Chebyshev spectral scheme. The effect of various parameters on the rate of heat transfer in the thermal boundary regime is investigated, i.e., thermal conductivity, the heat generation/absorption ratio and the mixed convection More >

Zhiqiang Wu^1,2, Yi Wu², Renjun Xie², Jin Yang¹, Shujie Liu³, Qiao Deng^4,*

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 399-406, 2023, DOI:10.32604/fdmp.2022.020402 - 29 August 2022

Abstract One of the main obstacles hindering the exploitation of high-temperature and high-pressure oil and gas is the sealing integrity of the cement sheath. Analyzing the microstructure of the cement sheath is therefore an important task. In this study, the microstructure of the cement sheath is determined using a CT scanner under different temperature and pressure conditions. The results suggest that the major cause of micro-cracks in the cement is the increase in the casing pressure. When the micro-cracks accumulate to a certain extent, the overall structure of the cement sheath is weakened, resulting in gas More >

Yukun Lv¹, Fan Yang^1,*, Zi’an Wei¹, Quan Lu²

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.2, pp. 379-397, 2023, DOI:10.32604/fdmp.2022.020373 - 29 August 2022

Abstract Leakage occurring in the tube sockets of the main steam thermometers can seriously threaten the safe operation of coal-fired power plants. Here, assuming a 300 MW unit as a relevant testbed, this problem is investigated numerically through solution of the equations of fluid-dynamics in synergy with the mathematical treatment of relevant statistics. The results indicate that the steam can form a large-scale spiral flow inside the tube socket and continuously scour the inner wall. In the model with the protective casing setting angle of 60°, the average tangential fluid velocity can reach up to 4.8 m/s,… More > Graphic Abstract