Jiaming Zhan^1,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.31, No.4, pp. 1-1, 2024, DOI:10.32604/icces.2024.011189

Abstract Calcium fluoride (CaF₂) exhibits excellent optical properties, making it a promising candidate for preparing optical components. The actual applications underscore the importance of enhancing the ductile machining of such a difficult-to-machine material. This study starts by investigating the influence of thermal gradient fields on the mechanical behaviors of CaF₂ single crystal experimentally and theoretically, revealing the potential deformation mechanisms under various thermal additions. On this basis, a novel laser-assisted machining (LAM) scheme was proposed to enhance the deformability and machinability of CaF₂ single crystal by tailoring local thermal fields. The laser heating spot within the work material… More >

Aouatif Saad^1,*, Mohammed EL Ganaoui²

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.1, pp. 95-103, 2023, DOI:10.32604/fdmp.2023.022014 - 02 August 2022

Abstract Resin transfer molding (RTM) is among the most used manufacturing processes for composite parts. Initially, the resin cure is initiated by heat supply to the mold. The supplementary heat generated during the reaction can cause thermal gradients in the composite, potentially leading to undesired residual stresses which can cause shrinkage and warpage. In the present numerical study of these processes, a one-dimensional finite difference method is used to predict the temperature evolution and the degree of cure in the course of the resin polymerization; the effect of some parameters on the thermal gradient is then More >

Rida Tazi¹, Adil Echchelh¹, Mohammed Hattabi², Mohammed El Ganaoui³, Aouatif Saad^4,*

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.1, pp. 223-232, 2023, DOI:10.32604/fdmp.2023.021976 - 02 August 2022

Abstract The successful manufacture of thick composites is challenging since the highly exothermic nature of thermoset resins and limited temperature control make avoiding the onset of detrimental thermal gradients within the composite relatively difficult. This phenomenon is mainly caused by exothermic heat reactions. The so-called Michaud's model has been largely used in the literature to reduce the gap between experience and simulation with regard to the effective prediction of the temperature cycle in these processes. In this work, another solution is proposed to simulate the curing process for thick composites, namely preheating the resin to activate More >

K. Khanna^1,2, V.K. Gupta³, S.P. Nigam¹

CMC-Computers, Materials & Continua, Vol.48, No.3, pp. 147-161, 2015, DOI:10.3970/cmc.2015.048.147

Abstract A mathematical model is developed to describe the steady state creep in a rotating Al-SiC_p disc having a non-linear thickness profile and distribution of SiC particles along the radial direction. The model is used to investigate the effect of imposing three different kinds of radial temperature profiles viz. linear, parabolic and exponential with fixed values of inner and outer surface temperatures, on the creep stresses and strain rates. It is noticed that by increasing the temperature exponent (n_T), the radial stress (over the entire radius) and tangential stress (near the inner radius) increase in the disc.… More >

M. M. Shemirani¹, M. Z. Saghir²

FDMP-Fluid Dynamics & Materials Processing, Vol.9, No.1, pp. 11-21, 2013, DOI:10.3970/fdmp.2013.009.011

Abstract Producing homogeneous single bulk crystals requires a good understanding of the thermo-solutal behavior in the solvent region. This study explores simulation of the growth of large diameter single bulk crystals of silicon and germanium alloy from its melt utilizing Bridgman method. Both thermal and solutal diffusion of silicon and germanium in the molten SiGe alloy are of interest. It was observed that the diffusion dominates the transport phenomenon in the solvent region especially in the first 25 mm of the model due to having a Pe_T <<1. It was also found that the control of both More >