Yongguo Li^1,2, Caiyin Xu^1,2,*, Can Qin^1,2, Dingjian Zheng^1,2

FDMP-Fluid Dynamics & Materials Processing, Vol.20, No.6, pp. 1251-1263, 2024, DOI:10.32604/fdmp.2023.044804 - 27 June 2024

Abstract The so-called ORC (Organic Rankine Cycle) heat recovery technology has attracted much attention with regard to medium and low temperature waste heat recovery. In the present study, it is applied to a Tesla turbine. At the same time, the effects of the disc speed, diameter and inter-disc gap on the internal flow field and output power of the turbine are also investigated by means of CFD (Computational Fluid Dynamics) numerical simulation, by which the pressure, velocity, and output efficiency of the internal flow field are obtained under different internal and external conditions. The highest efficiency More >

Yaofei Zhang¹, Guoxiang Li¹, Shuzhan Bai¹, Ke Sun^1,*, Guihua Wang^1,*, Yujie Jia², Zhengxian Fang²

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.11, pp. 2933-2951, 2023, DOI:10.32604/fdmp.2023.028804 - 18 September 2023

Abstract Multiphase simulations based on the VOF (Volume of Fluid) approach, used in synergy with the cavitation Schnerr-Sauer method and the K-Epsilon turbulence model, have been conducted to study the behavior of an injector nozzle as a function of relevant structural parameters (such as the spray hole diameter and length). The related performances have been optimized in the framework of orthogonal experimental design and range analysis methods. As made evident by the results, as the spray hole diameter increases from 0.10 to 0.20 mm, the outlet mass flow rate grows by 243.23%. A small diameter of More >

Yajing Zhang¹, Chaoyang Song², Zhiguo Li^2,*

Energy Engineering, Vol.120, No.2, pp. 501-510, 2023, DOI:10.32604/ee.2022.021423 - 28 November 2022

Abstract To overcome the problems of natural decreases in power quality, and to eliminate wind speed fluctuation due to wind shear and tower shadow effect arising from wind turbine structural parameters, an improved prediction model accounting for the dual effect of wind shear and tower shadow is, in this paper, built. Compared to the conventional prediction model, the proposed model contains a new constraint condition, which makes the disturbance term caused by the tower shadow effect always negative so that the prediction result is closer to the actual situation. Furthermore, wind turbine structural parameters such as More > Graphic Abstract

Wenbin Luo^1,*, Lingfeng Tang¹, Yuting Yan², Yifang Shi¹

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.4, pp. 869-899, 2023, DOI:10.32604/fdmp.2022.022280 - 02 November 2022

Abstract The aim of the study is to determine the optimal structural parameters for a plastic centrifugal pump inducer within the framework of an orthogonal experimental method. For this purpose, a numerical study of the related flow field is performed using CFX. The shaft power and the head of the pump are taken as the evaluation indicators. Accordingly, the examined variables are the thickness (S), the blade cascade degree (t), the blade rim angle (β1), the blade hub angle (β2) and the hub length (L). The impact of each structural parameter on each evaluation index is More >

Wenbin Luo^1,*, Youmin Wang¹, Yuting Yan², Yifang Shi¹, Zhendong Zhang³

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.3, pp. 789-813, 2022, DOI:10.32604/fdmp.2022.019691 - 22 February 2022

Abstract In order to determine the optimal structural parameters of a plastic centrifugal pump in the framework of an orthogonal-experiment approach, a numerical study of the related flow field has been performed using CFX. The thickness S, outlet angle β2, inlet angle β1, wrap angle, and inlet diameter D1 of the splitter blades have been considered as the variable factors, using the shaft power and efficiency of the pump as evaluation indices. Through a parametric analysis, the relative importance of the influence of each structural parameter on each evaluation index has been obtained, leading to the More >

Yifang Shi^*, Lingfeng Tang, Yinwu Tan, Wenbin Luo

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.3, pp. 713-736, 2022, DOI:10.32604/fdmp.2022.018434 - 22 February 2022

Abstract The structural design parameters of a plastic centrifugal pump were calculated and modeled, and flow field simulation analysis of the model was performed using CFD, in the framework of an orthogonal design method (or experiment). The inlet mounting angle β1, outlet mounting angle β2, wrap angle ϕ, and impeller inlet diameter D1 of the pump impeller were the four factors assumed for the application of the orthogonal experiment, using the efficiency and Net Positive Suction Head (NPSH) as evaluation indices. Moreover, taking the maximum efficiency and minimum NPSH of the plastic centrifugal pump as the More >

Jing Qian¹, Xuhong Miao², Yao Shen³

CMC-Computers, Materials & Continua, Vol.27, No.2, pp. 179-188, 2012, DOI:10.32604/cmc.2012.027.179

Abstract Based on experimental data, the research work on warp knitted spacer fabrics gives compression laws when structural parameters (such as diameter of spacer yarn, areal density, spacer yarn angle and the thickness of spacer fabrics ) of spacer fabric change. ANSYS calculation models were developed, and simulation results matched with experimental data well. The computer simulation on this area provides a fundamental tool which can help designer to decide structural parameters when working stresses are given. More >