Yubo Wang^1,2,*, Yanan Yu^1,2, Qiming Wang³, Anxun Liu³

FDMP-Fluid Dynamics & Materials Processing, Vol.20, No.9, pp. 1993-2006, 2024, DOI:10.32604/fdmp.2024.049510 - 23 August 2024

Abstract A model is proposed for liquid film profile prediction in gas-liquid two-phase flow, which is able to provide the film thickness along the circumferential direction and the pressure gradient in the flow direction. A two-fluid model is used to calculate both gas and liquid phases’ flow characteristics. The secondary flow occurring in the gas phase is taken into account and a sailing boat mechanism is introduced. Moreover, energy conservation is applied for obtaining the liquid film thickness distribution along the circumference. Liquid film thickness distribution is calculated accordingly for different cases; its values are compared More >

Sreedham Chandra Adhikari¹, Ratan Kumar Chanda¹, Sidhartha Bhowmick¹, Rabindra Nath Mondal¹, Suvash Chandra Saha^2,*

Energy Engineering, Vol.119, No.1, pp. 429-451, 2022, DOI:10.32604/EE.2022.018145 - 22 November 2021

Abstract Due to widespread applications of the bent ducts in engineering fields such as in chemical, mechanical, bio-mechanical and bio-medical engineering, scientists have paid considerable attention to invent new characteristics of fluid flow in a bent duct (BD). In the ongoing study, a spectral-based numerical technique is applied to explore flow characteristics and energy distribution through a loosely bent square duct (BSD) of small curvature. Flow is accelerated due to combined action of the non-dimensional parameters; the Grashof number Gr (=1000), the curvature (=0.001), and the Prandtl number Pr (=7.0) over a wide domain of the Dean… More >

Mohamed Omri^1,*, Yusuf Al-Turki², Ahmed A. Alghamdi¹, Amrid Amnache³, Luc G. Fréchette³

CMC-Computers, Materials & Continua, Vol.71, No.1, pp. 961-977, 2022, DOI:10.32604/cmc.2022.021406 - 03 November 2021

Abstract In this paper, three-dimensional flows in laminar subsonic cascades at relatively low Reynolds numbers (Re < 2500) are presented, based on numerical calculations. The stator and rotor blade designs are those for a MEMS-based Rankine microturbine power-plant-on-a-chip with 109-micron chord blades. Blade passage calculations in 3D were done for different Reynolds numbers, tip clearances (from 0 to 20%) and incidences (0° to 15°) to determine the impact of aerodynamic conditions on the flow patterns. These conditions are applied to a blade passage for a stationary outer casing. The 3D blade passage without tip clearance indicates More >

Peijian Zhou^1,2, Chaoshou Yan³, Lingfeng Shu⁴, Hao Wang², Jiegang Mou^2,*

FDMP-Fluid Dynamics & Materials Processing, Vol.17, No.5, pp. 871-886, 2021, DOI:10.32604/fdmp.2021.012250 - 05 July 2021

Abstract Single-channel sewage pumps are generally used to transport solid-liquid two-phase media consisting of a fluid and solid particles due to the good non-clogging property of such devices. However, the non-axisymmetric structure of the impeller of this type of pumps generally induces flow asymmetry, oscillatory outflow during operations, and hydraulic imbalance. In severe cases, these effects can jeopardize the safety and stability of the overall pump. In the present study, such a problem is investigated in the framework of a Mixture multiphase flow method coupled with a RNG turbulence model used to determine the structure of… More >

Tao Bian¹, Xin Shen², Jun Feng¹, Bing Wang^1,*

FDMP-Fluid Dynamics & Materials Processing, Vol.17, No.3, pp. 615-628, 2021, DOI:10.32604/fdmp.2021.014902 - 29 April 2021

Abstract In turbomachinery, strong secondary flow can produce significant losses of total pressure near the endwall and reduce the efficiency of the considered turbomachine. In this study, splitters located at different positions with respect to the main blade have been used to reduce such losses and improve the efficiency of the outlet guide vane (OGV). Three different relative positions have been considered assuming a NACA 65-010 profile for both the main blade and the splitter. The numerical results indicate that splitters can effectively reduce the total pressure loss by suppressing the secondary flow around the main More >

Obed Y.W. Abotsi, John P. Kizito^*

Frontiers in Heat and Mass Transfer, Vol.14, pp. 1-6, 2020, DOI:10.5098/hmt.14.24

Abstract In this paper, turbulent water flow and heat transfer are studied numerically in a pipe which is rotating about its longitudinal axis. Computations were conducted for axial Reynolds numbers ranging from 10000 to 30000 at different rotation rates. Rotation rate (N) is the ratio of the rotational Reynolds number to the axial Reynolds number. Predictions showed that the Nusselt number (Nu) of the stationary pipe (N=0) was augmented by 50-58% at N=5, 105-132% at N=10, 150-201% at N=15, 208-265% at N=20, and 320-373% at N=30. Improvements in the heat transfer rate was linked to the More >

Jiacheng Dai¹, Jiegang Mou^{1, *}, Tao Liu¹

FDMP-Fluid Dynamics & Materials Processing, Vol.16, No.2, pp. 161-179, 2020, DOI:10.32604/fdmp.2020.06613 - 21 April 2020

Abstract The automobile engine pump is an important part of the automobile cooling system, and has a direct influence on the engine performance. Based on the SST k-ω turbulence model, unsteady numerical simulation for an automobile engine pump with different tip clearances was carried out by Fluent. To study the flow field characteristics and pressure fluctuation, the characteristics of secondary flow distribution in volute are also analyzed. The result shows that the pressure fluctuation characteristics of the flow field show obvious periodic variation at different levels of tip clearances. The peak value of pressure fluctuation at… More >

Yong Guan¹, Wanling Hu^{1, 2, *}, Yun Zhang¹, Kewei Song^{2, 3}, Liangbi Wang^{2, 3}

CMES-Computer Modeling in Engineering & Sciences, Vol.123, No.1, pp. 237-256, 2020, DOI:10.32604/cmes.2020.09141 - 01 April 2020

Abstract The application of vortex generators in tube-finned heat exchangers is very universal. The vortex generators can generate secondary flow, and as we all know secondary flow can obviously strengthen heat transfer. To use vortex generators much more efficiently in the circle tube-finned heat exchangers, the intensity correlation study between secondary flow and heat transfer is needed. 22 different structures of circle tubefinned heat exchangers were numerically studied, including the plain fin cases and the cases with vortex generators. In addition, the influence of fin spacing, transverse and longitudinal tube pitch, heights and attack angle of More >

M. D. Shamshuddin^{1, *}, P. V. Satya Narayana²

FDMP-Fluid Dynamics & Materials Processing, Vol.14, No.1, pp. 57-86, 2018, DOI:10.3970/fdmp.2018.014.057

Abstract In the present paper, a numerical analysis is performed to study the primary and secondary flows of a micropolar fluid flow past an inclined plate with viscous dissipation and thermal radiation in a rotating frame. A uniform magnetic field of strength Bo is applied normal to the plane of the plate. The whole system rotates with uniform angular velocity about an axis normal to the plate. The governing partial differential equations are transformed into coupled nonlinear partial differential equations by using the appropriate dimensionless quantities. The resulting equations are then solved by the Galerkin finite More >