F. Khan^a, S. Noreen^a, M. S. Youssef^b, A. Jilani^c, H. T. Ali^b, G. Mustafa^d, M. Zahid^a,*

Chalcogenide Letters, Vol.22, No.9, pp. 807-820, 2025, DOI:10.15251/CL.2025.229.807

Abstract In this study Fe doped SnO₂-SnS₂ (FS) and Fe doped SnO₂-SnS₂-polypyrrole (FS-PPY) were synthesized and studied for the methylene blue (MB) egrdation under UV light. The morphological and structural characterizations were carried out by FTIR, SEM-EDX, XRD and XPS. It has been found that FS-PPy degrade methylene blue upto 98 % under optimized conditions as pH =3, dye concentration = 10 ppm, oxidant dose = 2 mM. The Langmuir-Hinshelwood kinetics model fitted well. The optimization was studied using response surface methodology. Scavengers study was carried out to find the active species. Reusability of photocatalyst was evaluated More >

Ziyang Niu^1,#, Xiaofen Wang^2,4,#, Yuanyuan Li^1,2,3,*, Zhuo He², Feng Huang¹, Qianjun Deng², Fei Hu², Qiongyu Zhou^2,*

Journal of Polymer Materials, Vol.42, No.1, pp. 57-80, 2025, DOI:10.32604/jpm.2025.060401 - 27 March 2025

Abstract Proton exchange membrane fuel cells (PEMFCs) have gained increasing interests as promising power sources due to their ability to convert hydrogen and oxygen directly into electricity with high efficiency and zero greenhouse gas emissions. Bipolar plates (BPs) are considered as a critical component of PEMFCs, serving to collect current, separate gases, distribute the flow field, and conduct heat. This paper reviews the technical status and advancements in BP materials, with special focus on strategies for enhancing interfacial contact resistance (ICR) and corrosion resistance through conductive polymer (CP) coatings. First, commonly used BP materials in PEMFCs More >

M. F. Elkady^1,2,*, E. M. El-Sayed², Mahmoud Samy³, Omneya A. Koriem¹, H. Shokry Hassan^4,5

Journal of Renewable Materials, Vol.12, No.2, pp. 369-380, 2024, DOI:10.32604/jrm.2023.046585 - 11 March 2024

Abstract In this study, green zinc oxide (ZnO)/polypyrrole (Ppy)/cellulose acetate (CA) film has been synthesized via solvent casting. This film was used as supporting material for glucose oxidase (GOx) to sensitize a glucose biosensor. ZnO nanoparticles have been prepared via the green route using olive leaves extract as a reductant. ZnO/Ppy nanocomposite has been synthesized by a simple in-situ chemical oxidative polymerization of pyrrole (Py) monomer using ferric chloride (FeCl₃) as an oxidizing agent. The produced materials and the composite films were characterized using X-ray diffraction analysis (XRD), scanning electron microscope (SEM), Fourier transform infrared (FTIR) and… More > Graphic Abstract

NORHABIBAH MOHAMAD^1,*, NOORDINI M. SALLEH^1,2, HABIBUN NABI MUHAMMAD EKRAMUL MAHMUD¹

Journal of Polymer Materials, Vol.40, No.3-4, pp. 165-189, 2023, DOI:10.32381/JPM.2023.40.3-4.4

Abstract The present study has explored the adsorption properties of polypyrrole-based adsorbents (polypyrrole and polypyrrole-polyethyleneimine composite) as novel conducting polymers in adsorbing methyl orange (MO) (an anionic dye) effectively from aqueous solution. The adsorption characteristics of the prepared polymer-based adsorbents were characterized by BET, FTIR, FESEM, and XRD methods. The effectiveness of PPy-based adsorbents for MO dye adsorption was examined using the batch adsorption method. Different parameters were changed during the adsorption process, including contact time, solution pH, and adsorbent dosage. The highest BET surface area of the PPy-PEI composite was found to be 11.85 m² /g,… More >

Samir Kamel^1,*, Ahmed A. Haroun², Amany M. El-Nahrawy³, Mohamed A. Diab¹

Journal of Renewable Materials, Vol.7, No.2, pp. 193-203, 2019, DOI:10.32604/jrm.2019.00144

Abstract In this work, conducting composites of nanocellulose (NC)/polypyrrole nanoparticles (NPPy) and silver nanoparticles (AgNPs), i.e., NC/NPPyAg, were synthesized for the first time, to the best of our knowledge, via in situ emulsion polymerization of pyrrole in the presence of surfactant dopants. The AgNPs acted as an oxidizing agent to simultaneously incorporate nanoparticles into the prepared composites. The structures and morphologies of the prepared composites were studied using Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), UV-Vis Spectra, thermogravimetric analysis (TGA), and scanning and transmission electron microscopy (SEM and TEM) techniques. Additionally, the prepared composites were characterized More >

Odin RAMÍREZ-FERNÁNDEZ^1,*, Rafael GODÍNEZ¹, Esmeralda ZUÑIGA-AGUILAR¹, Luis E. GÓMEZ-QUIROZ², María C. GUTIÉRREZ-RUIZ², Juan MORALES³, Roberto OLAYO³

BIOCELL, Vol.39, No.2-3, pp. 9-14, 2015, DOI:10.32604/biocell.2015.39.009

Abstract We have designed and evaluated a radial-flow bioreactor for three-dimensional liver carcinoma cell culture on a new porous coated scaffold. We designed a culture chamber where a radial flow of culture medium was continuously delivered through it. Once this system was established, flow was simulated using flow dynamics software based on numeric methods to solve Navier-Stockes flow equations. Perfusion within cell culture scaffolds was simulated using a flow velocity of 7 mL/min and found that cell culture medium was distributed unhindered in the bioreactor chamber. Afterwards, the bioreactor was built according to the simulated design More >