Wei Dong^1,2,3,4, Fuping Qian^5,*, Gang Li^1,*, Shi’an Zhou⁵, Lei Ding^2,4, Qingda Gao⁵, Xuemin Zeng¹

FDMP-Fluid Dynamics & Materials Processing, Vol.21, No.4, pp. 833-849, 2025, DOI:10.32604/fdmp.2024.056060 - 06 May 2025

Abstract Nitrogen oxides (NO_x) and particulate matter (PM) present significant risks to both human health and environmental sustainability. The Integrated Dust Removal and Denitrification Technology (DRDt) offers a more efficient and cost-effective solution for achieving ultralow industrial flue gas emissions; however, its effectiveness is undermined by low catalyst load rates and poor stability in filter materials. This study addresses these limitations by modifying conventional PTFE filter media (PTFE-Tim) through the incorporation of sodium alginate (SA) and dopamine (DA) as modifiers, resulting in two new filter materials: PTFE–SA–MOF and PTFE–DA–MOF. By optimizing the parameters of an orthogonal experimental… More >

Aihua Tao¹, Chao Li¹, Zhijun Jie¹, Yong Zhang¹, Xing Chen¹, Weili Liu^2,3,*

FDMP-Fluid Dynamics & Materials Processing, Vol.21, No.3, pp. 645-656, 2025, DOI:10.32604/fdmp.2025.059545 - 01 April 2025

Abstract Hydraulic sandblasting perforation plays a crucial role in the fracturing and reconstruction of unconventional oil and gas reservoirs. The jet nozzle is an essential part of the hydraulic perforation tool. Insufficient penetration depth, caused by excessive jet distances, presents challenges during the perforation process. To overcome this, an optimization design of the nozzle structure is required to enhance the perforation efficiency. In this paper, a computational fluid-dynamic model for conical-cylindrical nozzles has been elaborated. To further improve the rock-breaking efficiency of the jet nozzle, a fillet design is introduced at the nozzle inlet section. The… More >

Deyong Shang^1,2, Xi Zhang¹, Fengqi Liang¹, Chunde Zhai¹, Hang Yang¹, Yanqi Niu^1,2,*

CMES-Computer Modeling in Engineering & Sciences, Vol.139, No.2, pp. 2027-2041, 2024, DOI:10.32604/cmes.2023.045750 - 29 January 2024

Abstract When the amphibious vehicle navigates in water, the angle of the anti-wave plate and the position of the center of gravity greatly influence the navigation characteristics. In the relevant research on reducing the navigation resistance of amphibious vehicles by adjusting the angle of the anti-wave plate, there is a lack of scientific selection of parameters and reasonable research of simulation results by using mathematical methods, and the influence of the center of gravity position on navigation characteristics is not considered at the same time. To study the influence of the combinations of the angle of… More >

Weizhi Liao¹, Xiaoyun Xia^1,3, Xiaojun Jia¹, Shigen Shen^2,*, Helin Zhuang^4,*, Xianchao Zhang¹

CMC-Computers, Materials & Continua, Vol.76, No.3, pp. 3297-3323, 2023, DOI:10.32604/cmc.2023.040967 - 08 October 2023

Abstract As a new bionic algorithm, Spider Monkey Optimization (SMO) has been widely used in various complex optimization problems in recent years. However, the new space exploration power of SMO is limited and the diversity of the population in SMO is not abundant. Thus, this paper focuses on how to reconstruct SMO to improve its performance, and a novel spider monkey optimization algorithm with opposition-based learning and orthogonal experimental design (SMO³) is developed. A position updating method based on the historical optimal domain and particle swarm for Local Leader Phase (LLP) and Global Leader Phase (GLP) is… More >

Yanxian Wu¹, Shouming Zhong¹, Zhigang Guan¹, Lin Song¹, Kun Li², Jiarui Sun², Yuqiang Xu^2,*, Maochuan Tu³, Chaobin Fan³, Jinbin Yang⁴

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.1, pp. 261-271, 2023, DOI:10.32604/fdmp.2023.020076 - 02 August 2022

Abstract A three-dimensional model for the numerical simulation of casing-cement behavior is used to investigate residual strength in the perforated casing of ultra deep wells. The influence of the hole diameter, hole density and phase angle on the residual strength of the casing under non-uniform stress and fracturing conditions is revealed through the consideration of different perforation parameters. It is shown that the residual strength of the casing increases with the hole diameter and periodically changes with the hole density; the phase angle is the main factor that affects the residual strength of the perforated casing, More >

Weixing Zhang, Chunxia He^*

Journal of Renewable Materials, Vol.10, No.12, pp. 3263-3283, 2022, DOI:10.32604/jrm.2022.020516 - 14 July 2022

Abstract With the exponential growth of the computing power, machine learning techniques have been successfully used in various applications. This paper intended to predict and optimize the shear strength of single lap cassava starchbased adhesive joints for comparison with the application of artificial intelligence (AI) methods. The shear strength was firstly determined by the experiment with three independent experimental variables (starch content, NaOH concentration and reaction temperature). The analysis of range (ANORA) and analysis of variance (ANOVA) were applied to investigate the optimal combination and the significance of each factor for the shear strength based on… More >

Wenbin Luo^1,*, Youmin Wang¹, Yuting Yan², Yifang Shi¹, Zhendong Zhang³

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.3, pp. 789-813, 2022, DOI:10.32604/fdmp.2022.019691 - 22 February 2022

Abstract In order to determine the optimal structural parameters of a plastic centrifugal pump in the framework of an orthogonal-experiment approach, a numerical study of the related flow field has been performed using CFX. The thickness S, outlet angle β2, inlet angle β1, wrap angle, and inlet diameter D1 of the splitter blades have been considered as the variable factors, using the shaft power and efficiency of the pump as evaluation indices. Through a parametric analysis, the relative importance of the influence of each structural parameter on each evaluation index has been obtained, leading to the More >

Yuan Min^1,†, Xu Fengxiang^2,3,*, Wu Junhao¹, Zheng Xuefeng¹

Computer Systems Science and Engineering, Vol.35, No.3, pp. 173-181, 2020, DOI:10.32604/csse.2020.35.173

Abstract This paper studies the influence of different factors on pedestrian head injury in vehicle-pedestrian collisions. PC-Crash software is used to construct simulation experiments under ten factors. The research shows that the injury to pedestrians in reverse impact is greater than that to pedestrians in forward impact. With the acceleration of vehicle speed, the HIC value of pedestrians will increase with the increase of the height of the front hood from the ground. When the vehicle speed is less than 40 km/h, the injury to pedestrians in a forward-leaning emergency posture is smaller, and the injury More >