Shuaijun Wang¹, Wenqiong Tu^1,*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.25, No.2, pp. 1-1, 2023, DOI:10.32604/icces.2023.09926

Abstract Cellulose nanofibrils (CNFs) and the continuously assembled microfibers have shown transversely isotropic behavior in many studies. Due to fact that the size of CNFs and the assembled microfibers is at the nano and micro scale, respectively, the characterization of their mechanical properties is extremely challenge. That greatly hinders the accurate multi-scale modeling and design of CNFs-based materials. In our study, we have characterized the elastic constants of both CNFs microfibers and CNFs through a Multi-scale Optimization Inversion technology. Through the tensile test of CNFs microfibers reinforced resin with different volume fractions and the micromechanics model More >

Qiushi Li^1,2,#, Ronggang Luo^1,2,#, Yu Chen³, Jinhui Xiong³, Bei Qiao¹, Xijuan Chai^1,2, Linkun Xie^1,2, Juan Wang³, Lianpeng Zhang^1,2,*, Siqun Wang⁴, Guanben Du^1,2, Kaimeng Xu^1,2,*

Journal of Renewable Materials, Vol.11, No.6, pp. 2809-2822, 2023, DOI:10.32604/jrm.2023.026184 - 27 April 2023

Abstract To overcome the shortage of wood resources as well as to develop novel natural fibers materials, the Chimonobambusa quadrangularis (CQ) and Qiongzhuea tumidinoda (QT) planted in Southwest China were effectively isolated by the steam explosion (SE). The fine and uniform bamboo microfibers derived from CQ and QT were obtained, and their smallest average widths were 12.62 μm and 16.05 μm, respectively. The effects of steam explosion on the micro-morphology, chemical composition, thermal stability, crystallinity, surface wettability, and mechanical properties of bamboo microfibers were comprehensively investigated. The results showed that the relative content of cellulose in bamboo microfibers More > Graphic Abstract

Dounia Bendahou^1,2, Abdelkader Bendahou¹, Bastien Seantier¹, Bénédicte Lebeau³, Yves Grohens^1,*, Hamid Kaddami^2,*

Journal of Renewable Materials, Vol.6, No.3, pp. 299-313, 2018, DOI:10.7569/JRM.2017.634185

Abstract Hybrid aerogels have been prepared by freeze-drying technique after mixing water dispersions of cellulose microfibers or cellulose nanofibers and silica (SiO2) of type SBA-15 (2D-hexagonal). The prepared composites were characterized by different analysis techniques such as SEM, hot-filament, DMA, etc. These composites are compared to those previously prepared using nanozeolites (NZs) as mineral charge. The morphology studied by SEM indicated that both systems have different structures, i.e., individual fibers for cellulose microfibers WP-based aerogels and films for nanofibrillated cellulose NFC-based ones.... These differences seem to be driven by the charge of the particles, their aspect More >

Idalba A. Hidalgo A.^∗, Felipe Sojo^†, Francisco Arvelo^†, Marcos A. Sabino^∗,‡

Molecular & Cellular Biomechanics, Vol.10, No.2, pp. 85-105, 2013, DOI:10.3970/mcb.2013.010.085

Abstract The electrospinning technique is a method used to produce nano and microfibers using the influence of electrostatic forces. Porous three dimensional networks of continuous and interconnected fibers as scaffolds were obtained from a poly (lactic acid) solution. The concentration of the polymeric solution, 12.5% m/w, as well as the conditions of voltage (V=11kV) and tip-metallic collector distance (H=13cm) were established to develop these scaffolds through the electrospinning process. The characteristics of the scaffolds, such as fiber diameter, sintering and the biomimetics of the characteristics of a native extra cellular matrix were verified by Scanning Electron More >

A.N. Guz¹, J.J.Rushchitsky¹, I.A.Guz²

CMES-Computer Modeling in Engineering & Sciences, Vol.26, No.3, pp. 139-156, 2008, DOI:10.3970/cmes.2008.026.139

Abstract The basic approach is offered for problems of nanocomposites and their mechanical properties, which includes a short review of modern problems in nanomechanics of materials. The fibrous carbon-polymer composites with carbon or graphite microfibers or carbon nanotubes are especially discussed. The basic model of the linear or nonlinear elastically deforming micro- and nanocomposites is considered. Within the framework of this model, the comparative computer modeling is performed. The modeling permits to observe the features in prediction of values of basic mechanical constants. These results are utilized on next step of modeling -- studying the peculiarities More >