Ge Wang, Linbi Chen, Haiying Zhou^*, Shanyu Han, Fuming Chen^*

Journal of Renewable Materials, Vol.11, No.3, pp. 1499-1511, 2023, DOI:10.32604/jrm.2022.025130 - 31 October 2022

Abstract To overcome warping in thin bamboo bundle veneer laminated composites (TBLC), their hydrothermal deformation characteristics were systematically investigated in this study. It was found that TBLCs accelerated the release of internal stress in the thickness direction in a hydrothermal environment, which increased their warpage. TBLCs showed increased warpage in the width and diagonal directions upon increasing the temperature. The warpage of Type E increased by 155.88% and 66.67% in the width and diagonal directions, respectively, when the temperature increased from 25 C to 100 C. The symmetrical TBLC with cross-lay-up and odd layers displayed better More >

Lifeng Ji, Qiuxia Zhang, Fei Rao^*

Journal of Renewable Materials, Vol.10, No.9, pp. 2477-2487, 2022, DOI:10.32604/jrm.2022.021761 - 30 May 2022

Abstract Landscape designers increasingly prefer to use wood/bamboo-based composites for outdoor hydrophilic platforms owing to their natural surface texture, high performance, and sustainability to facilitate extensive interaction between people and water and enable the full range of ecological functions of water resources. In this study, four laminated composite (LC) structures were designed and manufactured using fluffed bamboo and wood veneers. Their surface textures, profile densities, water resistances, and mechanical properties were then evaluated. The type of fluffed veneer of the surface layer determined the texture of the LC surface. The specific structures of fluffed bamboo and More >

Jianchao Deng^1,2, Haiying Zhou², Fuming Chen², Shuangbao Zhang^1,*, Ge Wang^2,*

Journal of Renewable Materials, Vol.9, No.9, pp. 1555-1570, 2021, DOI:10.32604/jrm.2021.015461 - 23 April 2021

Abstract Elementary units “bamboo bundle” and “bamboo sliver” were processed and cross-linked as “bamboo-bundle veneer (BBV)” and “bamboo-sliver veneer (BSV)” for preparation of laminated composites. The concept of “high-content-adhesive surface treatment” was raised to improve boards’ performance, rather than increasing adhesive absorption of every layer’s porous unit. That is, some BBVs experienced an extra “dipping & drying” to absorb more resin (named “HBBV”). The effect of the amount of knitting threads was also discussed for influencing BBV’s quality. Results indicated that light transmittance of BBVs decreased as the amount of threads added from 3 to 8,… More >

M. Chatiri¹, A. Matzenmiller²

CMC-Computers, Materials & Continua, Vol.35, No.3, pp. 255-283, 2013, DOI:10.3970/cmc.2013.035.255

Abstract This article presents a three dimensional constitutive model for anisotropic damage to describe the elastic-brittle behavior of unidirectional fibrereinforced laminated composites. The primary objective of the article focuses on the three dimensional relationship between damage of the material and the effective elastic properties for the purpose of stress analysis of composite structures, in extension to the two dimensional model in Matzenmiller, Lubliner and Taylor (1995). A homogenized continuum is adopted for the constitutive theory of anisotropic damage and elasticity. Damage initiation criteria are based on Puck failure criterion for first ply failure and progressive micro More >

Christian Heinrich¹, Anthony M. Waas²

CMC-Computers, Materials & Continua, Vol.35, No.2, pp. 155-181, 2013, DOI:10.3970/cmc.2013.035.155

Abstract The smeared crack approach (SCA) is revisited to describe post-peak softening in laminated composite materials. First, predictions of the SCA are compared against linear elastic fracture mechanics (LEFM) based predictions for the debonding of an adhesively bonded double cantilever beam. A sensitivity analysis is performed to establish the influence of element size and cohesive strength on the load-deflection response. The SCA is further validated by studying the in-plane fracture of a laminated composite in a single edge bend test configuration. In doing so, issues related to mesh size and their effects (or non-effects) are discussed More >

Luiz F. Kawashita¹, Alexandre Bedos², Stephen R. Hallett³

CMC-Computers, Materials & Continua, Vol.32, No.2, pp. 133-158, 2012, DOI:10.3970/cmc.2012.032.133

Abstract A methodology is proposed for modelling transverse matrix cracks in laminated composites in a three-dimensional explicit finite element analysis framework. The method is based on the introduction of extra degrees of freedom to represent the displacement discontinuity and the use of a cohesive zone model to determine damage evolution and crack propagation. The model is designed for the analysis of matrix cracks in laminates made of uni-directional fibre-reinforced plies, allowing several assumptions to be made which greatly simplify the algorithm. This was implemented in the commercial software Abaqus/Explicit as a user-defined element subroutine (VUEL). The More >

K. Gordnian¹, H. Hadavinia¹, G. Simpson¹, A. Aboutorabi¹

The International Conference on Computational & Experimental Engineering and Sciences, Vol.1, No.2, pp. 61-68, 2007, DOI:10.3970/icces.2007.001.061

Abstract The compliance equation is used to calculate the energy release rate for angle ply laminated double cantilever composite beam specimen. Instead of the traditional approach of a beam on an elastic foundation, a second order shear thickness deformation beam theory (SSTDBT) has been considered. More >