Xiaoqian Bi¹, Pengfei Guan¹, Ping Li^2,*, Yuan Zhang¹, Xingong Li¹, Yingfeng Zuo^1,*

Journal of Renewable Materials, Vol.11, No.5, pp. 2399-2415, 2023, DOI:10.32604/jrm.2023.026656

Abstract Sodium silicate modification can improve the overall performance of wood. The modification process has a great influence on the properties of modified wood. In this study, a new method was introduced to analyze the wood modification process, and the properties of modified wood were studied. Poplar wood was modified with sodium silicate by vacuum-pressure impregnation. After screening using single-factor experiments, an orthogonal experiment was carried out with solution concentration, impregnation time, impregnation pressure, and the cycle times as experimental factors. The modified poplar with the best properties was selected by fuzzy mathematics and characterized by SEM, FT-IR, XRD and TG.… More > Graphic Abstract

Baian Shen, Haichao Li^*, Zixiang Guo, Jingxiao Li, Yuting Bao

Journal of Renewable Materials, Vol.11, No.1, pp. 185-195, 2023, DOI:10.32604/jrm.2023.020040

Abstract The activation effect of boric acid as an activator is good, and we investigate the best activation conditions for the boric acid impregnation method. To represent the structural characteristics and adsorption performance of the Stellera Chamaejasme based carbon molecular sieves, we use Brunner-Emmet-Teller (BET) measurements, scanning electron microscope (SEM), Raman spectra (Raman), X-ray diffraction (XRD), and adsorption property measurement. When the loading ratio was 0.68:1, the specific surface area was 532.21 m²/g, the total pore volume was 0.24 cm³/g, the average pore size was 1.81 nm, the adsorption value of methylene blue was 145.28 mg/g, and the adsorption value of iodine was 713.33 mg/g,… More >

Shun Kang¹, Xun Yuan¹, Changwu Liu^1,*, Yulin Chen¹, Xianliang Zhou¹, Haikuan Wu², Zhiguo Ma³

Journal of Renewable Materials, Vol.10, No.12, pp. 3521-3538, 2022, DOI:10.32604/jrm.2022.021694

Abstract Part of the tunnel spoil can not be used for concrete due to alkali-aggregate reaction (AAR). Water is an indispensable condition for AAR, so separating the alkali-aggregate from water is of great benefit to controlling the AAR. This paper investigates the modification of concrete and aggregate by hydrophobic impregnation and organic coating and then evaluates their waterproof and mechanical properties by dynamic contact angle (DCA), ultrasonic wave velocity, scanning electron microscope (SEM), nuclear magnetic resonance (NMR), and so on. For waterproofness, hydrophobic impregnation and organic coating can both improve the waterproofness of concrete and aggregate. The organic coating is suitable… More >

Pengfei Guan¹, Ping Li², Yiqiang Wu¹, Xingong Li¹, Guangming Yuan¹, Yingfeng Zuo^1,*

Journal of Renewable Materials, Vol.10, No.9, pp. 2451-2463, 2022, DOI:10.32604/jrm.2022.020459

Abstract To enhance mechanical properties and improve flame retardancy and smoke suppression of fast-growing poplar wood in wood applications, the wood was impregnated and modified. An organic phenolic prepolymer and inorganic sodium silicate was used as contrasting impregnation modifiers and wood samples were impregnated by a bionic “respiration” method with alternating positive and negative pressure. The weight percentage gain, density increase ratio, mechanical properties (bending and compressive strength and hardness), and water absorption rate of inorganic and organic-impregnated modified poplar wood (IIMPW and OIMPW, respectively) were compared and these properties in IIMPW were found to be higher than those of OIMPW… More >

Xiya Yu¹, Nianfeng Wei², Qisong Liu², Zhiyong Wu², Mizi Fan³, Weigang Zhao^1,*, Qinzhi Zeng^1,*

Journal of Renewable Materials, Vol.10, No.8, pp. 2041-2053, 2022, DOI:10.32604/jrm.2022.018027

Abstract To improve the mechanical properties of fast-growing Chinese fir (Cunnighamia lanceolate), expand its range of application, increase its value, and avoid the environmental pollution caused by impregnation with synthetic resin, Chinese fir was impregnated with a shellac solution. Since the shellac solution was difficult to penetrate into fast-growing Chinese fir, so microwave pretreatment was used to irradiate the wood to improve the permeability. This study investigated the effects of four factors, including the content of moisture in the wood before it was microwaved, the chamber pressure of microwave, the time of microwaving and the vacuum impregnation on the mechanical properties… More > Graphic Abstract

Marion Thébault¹, Larysa Kutuzova², Sandra Jury¹, Iris Eicher¹, Edith-Martha Zikulnig-Rusch¹, Andreas Kandelbauer^2,*

Journal of Renewable Materials, Vol.8, No.6, pp. 603-630, 2020, DOI:10.32604/jrm.2020.09616

Abstract Here, the effects of substituting portions of fossil-based phenol in phenol formaldehyde resin by renewable lignin from two different sources are investigated using a factorial screening experimental design. Among the resins consumed by the wood-based industry, phenolics are one of the most important types used for impregnation, coating or gluing purposes. They are prepared by condensing phenol with formaldehyde (PF). One major use of PF is as matrix polymer for decorative laminates in exterior cladding and wet-room applications. Important requirements for such PFs are favorable flow properties (low viscosity), rapid curing behavior (high reactivity) and sufficient self-adhesion capacity (high residual… More >

Charlotte Grosse^1,2,*, Marion Noël¹, Marie-France Thévenon³, Lauri Rautkari⁴, Philippe Gérardin²

Journal of Renewable Materials, Vol.6, No.3, pp. 259-269, 2018, DOI:10.7569/JRM.2017.634176

Abstract Impregnation of dry wood with pure lactic acid oligomers (OLAs) followed by heat treatment confers promising properties to wood because of OLA's good diffusion, in-situ polymerization and persistence in cell walls. Treatment provides drastic reduction of the equilibrium moisture content, high dimensional stability and good durability. The presence of water during treatment has been evaluated. Curing of OLA impregnated dry wood in humid atmosphere leads to a strong and global degradation of the material. OLA treatment of wet wood only impacts the water leaching rate negatively. Treatment of dry wood with OLA diluted in water additionally decreases the biological resistance… More >