Open Access

ARTICLE

V.S. Sampath Kumar, N.P. Pai^† , B. Devaki
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-13, 2023, DOI:10.5098/hmt.20.30
Abstract In the present study, we consider Casson fluid flow between two porous plates with permeability criteria in the presence of heat transfer and magnetic effect. A proper set of similarity transformations simplify the Navier-Stokes equations to non-linear ODEs with boundary conditions. The homotopy perturbation method is an efficient and stable method which is used to get solutions. Further, the results obtained are compared with the solution computed through an effective and efficient finite difference approach. The purpose of this analysis is to study the four different cases arise viz: suction, injection, mixed suction and mixed More >

View

786

Download

716

Open Access

ARTICLE

Erdiwansyah Erdiwansyah^a,e,f, Mahidin Mahidin^b,*, Husni Husin^b, Nasaruddin Nasaruddin^c, Asri Gani^b, Muhammad Faisal, Muhtadin Muhtadin^d, Muhammad Zaki^b, Rizalman Mamat^e
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-9, 2023, DOI:10.5098/hmt.20.29
Abstract The conversion of solid biomass waste into energy continues to be developed at this time to reduce dependence on fossil energy. Energy conversion can be carried out using several technologies commercialized by several industries, including the fluidized-bed combustor (FBC). This FBC technology has also been developed in several ways, such as the modification or unique modelling. In particular, the perforated plate modelling applied in this study is to provide excess air supply so that complete combustion can be achieved. In addition, modifying the perforated plate increases efficiency and radiation and reduces heat loss in the… More >

View

803

Download

815

Open Access

ARTICLE

Ummid I. Shaikh^a , Sonali Kale^b, Anirban Sur^c, Anindita Roy^c
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-10, 2023, DOI:10.5098/hmt.20.28
Abstract The requirement for sustainable development for buildings is to have environmentally friendly cooling and heating systems. The utilization of phase change materials (PCM) in the cooling system is a potential solution for minimizing active power requirements as well as for reducing the size of components of a vapor compression refrigeration VCR system. A prototype of an Air-PCM (T25™) heat exchanger was fabricated and tested in actual environmental conditions. Experimental trials using a salt hydrate as PCM have shown the maximum cooling effect of 2.05 kW when 75% of the PCM was solidified. Based on the More >

View

830

Download

830

Open Access

ARTICLE

Girma Tafesse^† , Mitiku Daba, Vedagiri G. Naidu
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-12, 2023, DOI:10.5098/hmt.20.27
Abstract Innovative technologies necessitate extra energy, which can be captured from environmentally sustainable, renewable solar energy. Here, heat and mass transfer through stirring nanofluids in solar collectors for direct absorption of sunlight are pronounced. The similarity transformation served to turn mathematically regulated partial differential equations into sets of nonlinear higher-order ordinary differential equations. These equations have been resolved by the homotopy analysis method manipulating, BVPh2.0 package in Mathematica 12.1. Validations are justified through comparison. Afterward, stronger magnetic field interactions delay the nanofluids mobility. Temperature increases with thermal radiation and Biot numbers. Entropy formation and nanoparticle concentration More >

View

776

Download

798

Open Access

ARTICLE

Yangyang Tian^a , Zhuo Chen^b,* , Qi Zhuang^c
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-11, 2023, DOI:10.5098/hmt.20.26
Abstract The cyclone separator has remarkable amplification effect, which is an important factor affecting its separation efficiency and pressure drop. The numerical simulation of Stairmand cyclone separators with cylinder diameters of 200, 280, 400, 480 and 600mm after geometric similarity amplification was carried out by ANSYS software. RSM model was used for gas phase and DPM model was used for particle phase. The results show that after the cyclone size is enlarged geometrically, the tangential velocity tends to increase with the increase of the cyclone barrel diameter at the same inlet gas velocity, which leads to… More >

View

1643

Download

1179

Like

3

Open Access

ARTICLE

Le Anh Duc^a , Pham Van Kien^b,*, Nguyen Thanh Tan^b, Doan Thanh Son^b, Nhanh Van Nguyen^c, Ngoc Xuan Nguyen^d
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-6, 2023, DOI:10.5098/hmt.20.25
Abstract This study focused on the heat and mass transfer in radio (RF) assisted heat pump (HP) drying of carrots. The experimental drying of carrot by RF assisted HP drying method was conducted to evaluate the effect of RF power on drying efficiency including drying rate and heating rate. The input drying parameters were drying air temperature of 45oC, drying air velocity of 2.5 m/s and RF power of 0, 0.5 and 1.5 kW, in which, RF power of 0 was corresponding to HP drying method. The experimental drying results showed that in RF assisted HP… More >

View

1051

Download

982

Open Access

ARTICLE

Xiaoyong Gu^a,*, Gang Wu^b, Biwen Chen^c
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-9, 2023, DOI:10.5098/hmt.20.24
Abstract To maintain the maximum temperature and temperature difference of batteries in electric vehicles within a reasonable range, a battery thermal management system combining closed air-cooling with phase change material(PCM) is proposed and investigated. A three-dimensional numerical model is developed and validated by experiment. The results indicate that the temperature rise of batteries decreases with the increase of ambient temperature. The increasing filling amount of PCM reduces the maximum temperature difference of batteries as well as the effect of the airflow rate on maximum temperature of batteries. The energy consumption is minimum when the filling amount More >

View

730

Download

835

Open Access

ARTICLE

Mohamed Shaimi^* , Rabha Khatyr, Jaafar Khalid Naciri
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-14, 2023, DOI:10.5098/hmt.20.23
Abstract This paper presents an exact analytical solution to the extended Graetz problem in microchannels and microtubes, including axial heat conduction, viscous dissipation, and rarefaction effects for an imposed constant wall temperature. The flow in the microchannel or microtube is assumed to be hydrodynamically fully developed. At the same time, the first-order slip-velocity and temperature jump models represent the wall boundary conditions. The energy equation is solved analytically, and the solution is obtained in terms of Kummer functions with expansion constants directly determined from explicit expressions. The local and fully developed Nusselt numbers are calculated in… More >

View

1041

Download

814

Like

1

Open Access

ARTICLE

Feng-Lin Zhou^a , Kai-Yuan Zhang ^a, Liang Cheng^b,† , Hai-Bing Cai^c, Yu-Liang Zhang^b, Min-Feng Lv^d
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-10, 2023, DOI:10.5098/hmt.20.22
Abstract In order to grasp the reverse startup characteristics of a small radial vane pump in the case of misoperation, a circulation piping system that includes the pump is established. Numerical simulation of the full three-dimensional unsteady incompressible viscous flow is performed based on the slip-grid technique and user-defined functions (UDF). According to the results, the static pressure fluctuation is small at the inlet of the centrifugal pump during the reverse startup, which differs significantly from the forward startup. Compared to the impeller rotational speed, the time required for the shaft power, head and flow curves… More >

View

702

Download

788

Open Access

ARTICLE

Ghaith Yahya Abusaibaa^a , Kamaruzzaman Sopian^a,*, Hasila Jarimi^a , Adnan Ibrahim^a, Saffa Riffat^b
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-6, 2023, DOI:10.5098/hmt.20.21
Abstract This study will demonstrate the performance of a photovoltaic (PV) powered vapour compression cooling system connected to a Phase Change Material (PCM) storage tank. Three options were studied, namely (a) PV vapour compression with a PCM storage tank and an air-conditioned room with chilled water circulation with transparent membrane/desiccant; (b) PV vapour compression with a PCM storage tank and an air-conditioned room with chilled air dehumidification; and (c) PV vapour compression with a PCM storage tank and an air-conditioned room chilled by combined water circulation, a transparent membrane/desiccant, and air duct dehumidification. Simulation using TRNSYS,… More >

View

751

Download

794

Open Access

ARTICLE

Qais Abid Yousif^a , Omar Rafae Alomar^a,*, Obed M. Ali^b , Omar Mohammed Ali^c
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-14, 2023, DOI:10.5098/hmt.20.20
Abstract This work involves a numerical investigation on free convection heat transfer occurred by a hot cylinder immersed in a square duct cooled from one side under different temperatures. Simulations have been done for a large ranges of Rayleigh number (10³ ≤ Ra ≤10⁷ ) and right wall temperature (0≤T_r ≤0.75). The results displayed that Nu is enhanced with rising in Ra and decreasing in T_r. The value of Nu is decreased with rising in T_r, where the maximum reduction in Nu is about 32% for T_r=0.75 as compared to T_r=0. The maximum enhancement range for Nu is found between 50% and 100% More >

View

817

Download

768

Like

1

Open Access

ARTICLE

Xuehui Jing^a,* , Wei Li^a, Zhaoyu Li^a , Zhiyun Wang^b
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-4, 2023, DOI:10.5098/hmt.20.19
Abstract This paper numerically simulates the combustion in a 300MW tangentially fired pulverized high-alkali coal boiler under low-load conditions. The combustion process, temperature distribution and the thermal load in the furnace at different height are analyzed under three different load conditions, which are 30%, 45% and 60% of full load. The temperature distribution and the variation of NO_x concentration under different load conditions are investigated, as well. The results show that the combustion processes of pulverized high-alkali coal in the furnace are similar under different load conditions, but the positions of the fuel’s full combustion are related… More >

View

866

Download

872

Open Access

ARTICLE

Ameer Abed Jaddoa^* , Karema Assi Hamad, Arshad Abdul Jaleil Hameed
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-9, 2023, DOI:10.5098/hmt.20.18
Abstract In the Heat Transfer process, many innovations were introduced aiming to obtain the most optimum behavior of the cooling process using nanofluids as coolant liquids. These nanofluids have gained much attention in cooling systems due to their special rheological and thermal performance. In this work, an experimental evaluation is conducted for nanofluids Al₂O₃, SiO₂, CuO, ZnO, and TiO₂ nanoparticles applied to a mini-channel. The nanofluid particles were entirely spread out in purified water (size of 15 nm) before being passed to the heat sink through a confined inflow channel. The obtained results showed that the achieved improvement… More >

View

724

Download

840

Open Access

ARTICLE

Hussein Al-Gburi^*, Akeel Abbas Mohammed, Audai Hussein Al-Abbas
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-7, 2023, DOI:10.5098/hmt.20.17
Abstract Transferring thermal energy efficiently necessitates utilizing a heat exchanger capable of producing the full thermal power of the energy supply at lowest possible cost and time. Therefore, in the present investigation, the impact of corrugated helical coil concentric tube-in-tube heat exchanger on the thermal performance is investigated experimentally. As a continuous in our issue of heat exchanger, the corrugated helical tube-in-tube is carried out and compared with smooth helical tube-in-tube for free convection heat transfer. The set-up of the experimental apparatus are designed and utilized to be appropriate for the cooling and heating systems of… More >

View

781

Download

818

Open Access

ARTICLE

O. M. Oyewola^a,b,* , M. O. Petinrin^a , and H. O. Sanusi^a
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-8, 2023, DOI:10.5098/hmt.20.16
Abstract The flow and heat transfer behaviour of channels with dimples and protrusions of spherical and piriform shapes was numerically explored by solving the Navier-Stokes and energy equations with a CFD software, the ANSYS Fluent 19.3, in the range of Reynolds numbers from 8,500 to 59,000. The values of the Nusselt number and friction factors were estimated and the non-dimensional Performance Evaluation Criterion (PEC) was determined to measure the thermal-hydraulic performance. The results reveal that the piriform protruded channel demonstrated a higher thermal performance with Nusselt number values of 36%, 15%, 23%, and 9% than the… More >

View

775

Download

835

Open Access

ARTICLE

Wenhua Liu^a,b, Mo Yang^c,a,*, Yuwen Zhang^b , Guiliang Liu^a , Liang Ling^a , Xuchen Ying^a,*
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-7, 2023, DOI:10.5098/hmt.20.15
Abstract In this study, numerical investigations are performed on a partially premixed flame of methane and air in two- and three-dimensional models. Nonlinear method is adopted to illustrate the asymmetric phenomenon that affects the flame stability under various co-flow velocities. According to the results, the mathematical relationship between the flame flickering frequency Stanton number and the dimensionless velocity Froude number has been summarized as St=0.7Fr^-0.46. The bifurcation phenomena under different Reynold numbers are found to have significant influence on the system stability. Two critical bifurcation points, which is when Re=300 and Re=1200, are determined as the onset More >

View

750

Download

821

Open Access

ARTICLE

Linfang Fang, Fuyong Su^* , Zhen Kang, Haojun Zhu
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-9, 2023, DOI:10.5098/hmt.20.14
Abstract Taking the ladle used by a factory as an example, a three-dimensional finite element model of the ladle was established, and the temperature distribution law of the lining during the ladle transportation was studied using the finite element analysis software ANSYS, which verified the good thermal insulation performance of the nano thermal insulation layer, and analyzed and compared the temperature and distribution law of the refractory lining under the two working conditions of the heavy ladle and the empty ladle. The results show that due to the change of the boundary conditions in the empty More >

View

812

Download

834

Open Access

ARTICLE

Qi Zhuang^a,* , Dong Liu^b, Bo Liu^c, Mei Liu^a
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-6, 2023, DOI:10.5098/hmt.20.13
Abstract In the actual operation of wet gas pipeline, liquid accumulation is easy to form in the low-lying and uphill sections of the pipeline, which leads to a series of problems such as reduced pipeline transportation efficiency, increased pipeline pressure drop, hydrate formation, slug flow and intensified corrosion in the pipeline. Accurate calculation of liquid holdup is of great significance to the research of flow pattern identification, pipeline corrosion evaluation and prediction, and gas pipeline transportation efficiency calculation. Based on the experimental data of liquid holdup in horizontal pipeline, a commonly used BP neural network (BPNN)… More >

View

717

Download

828

Open Access

ARTICLE

Tieming Wang^a , Fuyong Su^b,*
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-4, 2023, DOI:10.5098/hmt.20.12
Abstract This paper analyzes the power generation technology of coke dry quenching (CDQ) waste heat boiler, and compares the exergy efficiency of medium temperature medium pressure boiler and high temperature high pressure boiler. The scheme of high temperature ultrahigh pressure primary intermediate reheat boiler to further improve the power generation efficiency of CDQ waste heat is put forward, and the exergy efficiency is analyzed. The bottleneck problem of further improving power generation efficiency by CDQ waste heat power generation and the exergy efficiency limit under the current process conditions are obtained. More >

View

889

Download

845

Open Access

ARTICLE

Yu-Liang Zhang^a,* , Dong-Yang Wu^b, Hai-Bing Cai^c, Can-Fei Wang^c, Fei-Wu^c, Shao-Han Zheng^d
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-5, 2023, DOI:10.5098/hmt.20.11
Abstract In this paper, based on the Mixture model, the numerical computations of the internal flow field in a sewage pump are carried out. Through numerical simulation, the turbulence flow characteristics in the sewage pump are obtained. Results show that when the particle diameter is 0.10 mm, the solid-phase concentration on the volute surface is high, and the wear is more severe. When the particle diameters are 0.15 mm and 0.20 mm, the solid-phase concentration on the volute surface is significantly higher, especially when the over-current cross-section enlarges constantly. More >

View

737

Download

794

Open Access

ARTICLE

L.H. Tong^a , Y.L. Zhang^b,†, T.H. Yu^a, B.Y. Luo^c, J.F. Li^b
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-8, 2023, DOI:10.5098/hmt.20.10
Abstract In order to explore the thermal characteristics of a small nozzle flowmeter in the solid domain when transporting medium with different temperatures, the steady and transient thermal characteristics of each component of the nozzle flowmeter are calculated based on the finite element method. Results showed that the numerical calculation method could effectively reveal the internal thermal characteristics. When transporting high temperature medium, there was an obvious temperature stratification near the inner wall; when the inner wall temperature rose from 50 °C to 700 °C, the heat flow field at the inlet and outlet of the More >

View

881

Download

813

Open Access

ARTICLE

Mirmanto Mirmanto^a,*, Syahrul Syahrul^a, Agung Tri Wijayanta^b
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-5, 2023, DOI:10.5098/hmt.20.9
Abstract A study to examine the effect of evaporator diameters on the performances of a custom air-water generator had been conducted in naturally room air temperatures. Performances in this study consisted of fresh water production, coefficient of performance, and total heat transfer from the air. The freshwater was attained from the dew that dropped from the evaporator walls. It was from water vapour in the air that condensed due to the low temperature of the evaporator walls. The evaporator which had dimensions of 285 mm x 12.7 mm x 480 mm was placed in an open More >

View

851

Download

811

Open Access

ARTICLE

M. El-Bayoumi^a,†, A. M. Abouel-Fotouh^a, Amal El Berry^a
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-6, 2023, DOI:10.5098/hmt.20.8
Abstract Ram pumps employ renewable energy in the form of water head to pump water, but they have performance issues that require difficult on-site testing and tuning, hence limiting their application. The current research developed a low-cost lab-scale testing system for small ram pumps’ performance evaluation, tuning and leak testing. The developed system is made from available, low-cost, sensors and components. It conserves test water by setting the supply head through continuous circulation of water. The system was tested on a low-cost small sized ram pump, specially built using plumbing components. Test results demonstrated the capacity More >

View

814

Download

800

Open Access

ARTICLE

Muhammad Amin Murad^a,*, Faraidun Hamasalh^b, Hajar F. Ismael^c
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-8, 2023, DOI:10.5098/hmt.20.7
Abstract In this paper, we study the behavior of heat transfer of Casson fluid at the magnetohydrodynamic stagnation point with thermal radiation over a continuous moving sheet. The appropriate similarity transfer is used to transfer the governing differential equations into the ordinary differential equation and then solved by the collocation method based on spline function. The obtained results are investigated with the existing literature by direct comparison. We found that an increment in the value of the shrinking parameter, magnetic parameter, and Casson fluid parameter enhances the velocity distribution and depreciate the temperature profile both Casson More >

View

1005

Download

883

Open Access

ARTICLE

Ameer Abed Jaddoa^* , Hussain Saad Abd
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-12, 2023, DOI:10.5098/hmt.20.6
Abstract In this work, the demeanour of heat transfer in a cooled upstanding turbulent flow condition of supercritical carbon dioxide SC- CO2 was investigated and analyzed. Several scenarios were adopted to handle the experimental data acquired by applying a perpendicular pipe with bending tape used in the examination model. The outcomes were presented using a typical method 'the dimensionless constitution'. Also, a modification was achieved to improve the relationship among the parameters for the processes of up and down flows. The achieved results will help address this research gap on turbulent perpendicular compound heat load based More >

View

991

Download

833

Open Access

ARTICLE

D. Santhi Kumari^a,* , Venkata Subrahmanyam Sajja^a , P. M. Kishore^b,†
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-11, 2023, DOI:10.5098/hmt.20.5
Abstract The aim of present study is an influence of viscous dissipation and heat source on an unsteady MHD mixed convective, fluid flow past an impulsively started oscillating plate embedded in a porous medium in presence of magnetic field, heat and mass transfer. The modeling equations are converted to dimensionless equations then solved through Galerkin finite element method and discussed in the flow distributions with the help of MATLAB. Numerical results for the velocity, temperature and concentration distributions as well as the skin-friction coefficient, Nusselt number and Sherwood number are discussed in detail and displayed graphically More >

View

906

Download

909

Open Access

ARTICLE

Ahmad Shafique^a , Muhammad Ramzan^a,*, Zubda Ikram^a, M. Amir^a, Mudassar Nazar^a
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-10, 2023, DOI:10.5098/hmt.20.4
Abstract Unsteady flow of fractionalized Jeffrey fluid over a plate is considered. In addition, thermo diffusion and slip effects are also used in the problem. The flow model is solved using Constant proportional Caputo fractional derivative. Initially, the governing equations are made non-dimensional and then solved by Laplace transform. From the Figs., it is observed that Prandtl and Smith numbers have decreasing effect on fluid motion, whereas thermodiffusion have increasing effect on fluid motion. Moreover, comparison among fractionalized and ordinary velocity fields is also drawn. More >

View

1057

Download

998

Open Access

ARTICLE

Ammar Hassan Soheel^a,*,†, Johain J. Faraj^b, Fawizea M. Hussien^b
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-11, 2023, DOI:10.5098/hmt.20.3
Abstract The household batch reactor using cow manure as the substrate generates methane gas used as fuel. This paper presents two-dimensional (3D) axisymmetric using commercial COMSOL 5.5 Multiphysics software. This is a computational fluid dynamics (CFD) model based on conservation equations with the chemical reaction model of anaerobic digestion (AD) processes to investigate the influence of different horizontal circular extended surfaces augmented to the inside digesters on the performance of the anaerobic digestion. Using four batch digesters, D1 with no extended surfaces and D2, D3, and D4 have augmented with four horizontal circular extended surfaces of More >

View

971

Download

945

Open Access

ARTICLE

HM Iqbal Mahmud^a,b,*,† , Vijay Rajaram^b, Khalid Moinuddin^b
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-17, 2023, DOI:10.5098/hmt.20.2
Abstract This study has examined some important aspects of the engineered smoke control system, namely the shape of smoke reservoirs and the quantity and distribution of smoke extract points within a smoke compartment. Three different shapes of smoke reservoirs have been selected for analysis, namely square, rectangular, and T-shaped. The shape of the smoke reservoir has been varied, but the area, length and height have been kept identical. Four different configurations of extract points have been used in each shape of the reservoir: a single extract point located at the corner of the smoke reservoir, a… More >

View

843

Download

896

Open Access

ARTICLE

Rajen Kumar Nayak^a,* , Ravi Shankar Prasad^a,† , Ujjwal Kumar Nayak^a , Amit Kumar Gupta^b
Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-9, 2023, DOI:10.5098/hmt.20.1
Abstract Inserting the jet plate between the bottom plate and absorber plate in a flat plate solar air heater has been proposed as an excellent option to enhance the performance of the conventional solar air heater. This research work presents an experimental study of flow and heat transfer in a jet plate solar air heater. Results are presented for the different mass flow rates of air ṁ1 and ṁ2, Reynolds number Rej_a2, streamwise pitch of the holes to jet hole diameter X/D, depth of upper channel to jet hole diameter Z₂/D, fixed number of jet hole N and angle More >

View

2279

Download

1475